|
| Control Systems & Process Instruments Lab |
DC Servo Motor
Study Unit |
|
|
Transfer Function
Using Op-Amp |
|
PID Controller
(Analog Version) |
|
Control Systems & Process Instrumentation Lab
(For the order you can follow by the model no. item name as given in the image)
HiQ make Control Systems engineering lab Trainer kits have been designed to suit the engineering Institutions. In training and to make understand the concepts of various techniques adopted in the areas of an electronics control & instrumentation engineering. All these units are self contained supplied with all necessary circuitry with a built-in Power supply & Signal Generators. And the functional block diagram of the each section is printed on a front panel and the test points & controls brought outside from the pcb and terminated them on a panel. So that at an every stage the signal can be measured and verified the results. Each module is enclosed in an attractive powder coated metal boxes. With in-built power supply and signal sources, user only have to add the oscilloscope to perform the various experiments independently. |
 |
Lead Lag Compensation Design |
|
List of experiments covered:
- Study of simple phase lag network
- Study of simple phase lead network
- Study of lag compensation
- Study of lead compensation
- Study of lead-lag compensation
|
Lead Lag Compensation
Design Trainer |
|
|
| |
|
|
|
Simulation of Transfer Function |
|
List of experiments covered:
- Verification of first order transfer function
- Verification of 2nd order transfer function
- Verification of 3rd order transfer function
|
Simulation of
Transfer Function |
|
|
| |
|
|
|
PID Controller Analog Version |
|
List of experiments covered:
- Time domain response of PID controller
- Proportional control
- Study of PI control
- Study of PID control
- PID design by process reaction curve method
|
PID Controller
(Analog Version) |
|
|
| |
|
|
|
PID Controller Microprocessor Based |
|
List of experiments covered:
- Identification of over parameters
- On/off control
- Proportional control
- Proportional, Integral control
- Proportional, Integral & Derivative control
|
PID Controller
(Microprocessor Version) |
|
|
| |
|
|
|
PID Controller PC Based |
|
List of experiments covered:
- Study of P, I & D characteristics by setting each parameter individually
- Study of PID all three parameters can be set at time and
The graphical representation can be viewed on a pc in a closed
Loop system
The PID unit supplied with Temperature simulator kit, RS 232 serial cable
And software. Which enables the students to carry out the experiments on a pc?
And the effect of P, I & D can be studied on a closed loop system along with
Temperature loop.
|
Control System
Engineering Lab |
|
|
| |
|
|
|
Magnetic Amplifier |
|
List of experiments covered:
- Study of series connected magnetic amplifier
- Study of parallel connected magnetic amplifier
- Study of self saturated magnetic amplifier
|
|
| |
|
|
|
Linear System Simulator |
|
List of experiments covered:
- Open loop step response of 1st order system
For various values of gain
- Closed loop step response of 1st order system
For various values of gain
- Open loop response of 2nd order system
- Closed loop response of 2nd order system
- Response of 3rd order system
|
|
| |
|
|
|
DC Motor Generator Study |
|
List of experiments covered:
- DC Motor-Generator characteristics
- Torque-speed characteristics
- Step response of the motor
- Simulation of Motor transfer function
|
DC Motor Generater
Study Unit |
|
|
| |
|
|
|
DC Servo Motor Study |
|
List of experiments covered:
- DC motor speed control
- torque characteristics
|
DC Servo Motor
Study Unit |
|
|
| |
|
|
|
AC Servo Motor Study |
|
List of experiments covered:
- AC motor speed control
- AC motor torque characteristics
|
|
| |
|
|
|
PLC Demonstrator |
|
List of experiments:
- Programming of registers, timer and counter using ladder software
- Study and verification of truth tables of logic Gates using ladder software
- verification of Boolean expressions
- interface and programming of a stepper motor
Accessories supplied:
Windowed based Ladder software -1
4mm patch cords -1Set; user’s manual -1Book;
3pin power cord & spare fuse -1each.
Optional Accessories required:
- 20MHz/30MHz dual channel Analog or Digital Storage oscilloscope
with an Alt. triggering facility.
- 31/2 Digit, Digital Multimeter
Accessories:
The following accessories supplied along with the each unit
User’s Manual -1Book
4mm patch cord -1Set
3Pin power cord & Spare fuse -1each |
|
| |
|
|
|
